Apogee Symphony 64 ThunderBridge Instrukcja Użytkownika Pobierz pdf

Symphony System Release 4.5 New Features

•

Enables the use of Apogees ThunderBridge interface with Thunderbolt equipped Macs.

Who Should Update

•

New Users of Apogees Symphony 64 | ThunderBridge interface, for use with Thunderbolt

equipped Macs.

•

This release or previous release 4.4 are required for Symphony I/O systems equipped with the

2x6 Analog I/O Module.

•

This release is compatible with Mac OSX 10.7.4, 10.7.5, 10.8.2 and later, it is not compatible with

OSX 10.6.8

•

New Users of Symphony | ThunderBridge using supported Legacy 16X or Rosetta Series

interfaces, see Legacy Interface Release 4.5 Notes for complete list of compatible conﬁgurations.

Who Should Remain on Previous Releases.

•

Symphony I/O Users running Mac OSX 10.6.8 or lower

•

Any Symphony I/O User who is NOT using Symphony 64 | ThunderBridge with a ThunderBolt

equipped Mac

Important Note concerning the Symphony I/O Firmware Updater:

• OSX 10.8.0 does not work, the OS must be updated to version 10.8.2, or 10.7.5 can be used.

• The ﬁrmware updater is not compatible with USB 3 ports on recently introduced Macs.

Workaround - connect Symphony I/O’s USB port to a USB 2 hub (including a Mac keyboard),

then connect the hub to the USB 3 port.

Before you update

• Please note critical Maestro settings such as Trim levels before performing a ﬁrmware update.

Parameters will be reset after installing new software.

• Unplug headphones and mute speaker volume before updating ﬁrmware.

To update

1. Update Symphony I/O ﬁrmware via USB - for details, please see the document Updating

Symphony I/O Firmware included in this release package.

2. Double-click the Symphony I/O Software Installer and follow the instructions provided by the

installation application.

3. You will be required to re-start your computer once installation is complete.

After updating - After updating, verify the following settings;

• Audio Interface Mode - press and hold the right hand encoder to verify that Symphony I/O is set

to the desired audio interface mode.

•

If using either the Symphony 64 card or ThunderBridge, verify that the Symphony Source setting

(found in the Maestro 2 > System Setup tab and Audio MIDI Setup) is set to the appropriate

Symphony Source Port setting:

! ! If interfaces are connected only to Port 1, set Source to Port 1 Chs 1-32.

! ! If interfaces are connected to both Ports 1-2, set Source to Ports 1-2 chs 1-64.

• Check that Output settings such as Speaker setting and level and headphone level and mute are

set as expected.

Apogee Electronics 1715 Berkeley Street • Santa Monica, CA 90404 USA • Tel: +1 (310) 584-9394 www.apogeedigital.com

Symphony System Release 4.5 Notes

1 2

Podsumowanie treści

Strona 1

Symphony System Release 4.5 New Features•Enables the use of Apogees ThunderBridge interface with Thunderbolt equipped Macs.Who Should Update•New Users

Strona 2

Known Issues• Save-Recall : If a Maestro Setup ﬁle is opened and the user chooses Sleep on the Mac, Maestro reverts to a state where the Setup ﬁle doe

Komentarze do niniejszej Instrukcji

Brak uwag

Apogee Symphony 64 ThunderBridge Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Koncentratory interfejsów Apogee Symphony 64 ThunderBridge. Symphony I:O Release 4.5 Notes [en] Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji